Ducati

This is the single-sided rear swingarm for the 2023 Ducati Panigale V4S. Part is off a Good Running 2023 Ducati Panigale V4S , with 5,537 Miles

Stamped aluminum heat shield plate located under the rider/passenger seat.; Protects the subframe and electronics from exhaust heat.; Features specific cutouts for subframe mounting points and wiring...

Technically the 'Rear Fairing Lower Cover' or 'Undertray'.; Mounts under the tail section, shielding the subframe and exhaust from road debris.; Fits Ducati Panigale V4, V4S, V4R, and SP2 models...

Technically the 'Rear Wheel Spindle'.; Includes the 4 integrated drive pins (studs) on the flange.; Bearing surfaces show normal wear patterns and red grease residue (Shell Gadus S2, factory spec).;...

Technically the 'Right Side Shock Bracket Holder' or Rear Engine Mount Bracket.; Mounts to the rear of the engine case and provides the mounting point for the rear shock linkage or pivot.; Cast...

Damaged: Cracked, Main right side fairing panel for 2022+ Panigale V4 models (updated aero vents).; Features 'DUCATI PANIGALE' black lettering.; Includes inner sound deadening foam.; Technically...

Commercial name: Right Rear Tail Fairing or Seat Cowl Side Panel.; Technical: ABS plastic fairing that covers the side of the rear subframe/tail section.; Fitment: Shared between Panigale V4 and...

This is the plastic support panel or trim piece that fits under the passenger seat or tail section. It is also referred to as a Pillion Seat Support Panel.; OEM Pattern Match (Text) Part is off a...

Technically the 'Secondary Air System Actuator' or 'Solenoid Valve'.; Commonly called the 'PAIR Valve', 'AIS Valve', or 'Smog Valve'.; Controls the injection of fresh air from the airbox into the...

Scuffed, This is the main side fairing assembly, which includes the upper red portion and the lower black spoiler/winglet. Part is off a Good Running 2023 Ducati Panigale V4S , with 5,537 Miles

Bare side stand leg only; does not include spring, pivot bolt, or sensor.; Fits Ducati Panigale V4, V4S, V4R, and Speciale models (2018-2024).; Stamped number is 556.1.114.1AA. Part is off a Good...

This is a complete OEM rear sprocket and cush drive carrier/flange assembly. It includes the six cush drive dampers. The stock sprocket size for a Panigale V4 is a 41 tooth, 525 pitch. Part is off a...

This part is the right-hand subframe closing panel, which is a component of the fairing assembly.; Part is off a Good Running 2023 Ducati Panigale V4S , with 5,537 Miles

Commercially known as the Left Tail Side Fairing or Left Rear Body Panel.; Fits 2018+ Ducati Panigale V4/V4S and Panigale V2 models.; Molded number 482.1.689.1A is the primary identifier used in the...

Technically an NTC Thermistor used to measure Ambient or Intake Air Temperature.; Features distinctive metal spring clips on the mounting wings for secure fitment into the air duct.; Protected by...

Technically a Gearbox Position Sensor or Neutral Switch that reads the internal shift drum position via sliding brush contacts.; Features a braided protective cable sheath and a 2-pin grey connector...

Technically a Dual-Bore Electronic Throttle Body (ETV) unit.; This unit controls air intake for two of the four cylinders (one bank).; Features integrated servo motor for Ride-By-Wire control.;...

Transmission Bearing Flange (Main Shaft) - Aluminum housing with integrated bearing. Fits 2018-2024 Ducati Panigale V4, V4S, V4R, and Streetfighter V4. Good used condition, bearing appears smooth, no...

Transmission Shift Drum & Forks Set - Complete assembly includes shift drum (182P0011A), 3 selector forks, 2 guide shafts, detent star, and gear position sensor (552.1.631.1A). Fits 2018-2024 Ducati...

Technically the 'Fixed Lower Intake Funnel' or 'Intake Manifold Pipe' for the Variable Intake System.; Each unit covers two cylinders (one bank). The set includes both the Front and Rear bank bases.;...